重庆大学主页平台管理系统周杰--中文主页--论文成果

周杰

同专业硕导同专业博导

最后更新时间：--

中文主页 - 科学研究 - 论文成果

论文成果

庞佳丽,祝泽林(学),庞佳丽(学),张靖宇(学),Chen, Q(外),周杰,Sugiyama, S(外).Thermal forming properties of a Cr-Mn-Si-Ni alloyed naval steel under different forming conditions by different constitutive models:RARE METALS,2022,41):3515-3529
余盈燕,屈志远(学),张建生,周杰.Influence of Surfacing Fe-Based Alloy Layers on Wire Arc Additive Manufactured Ni-Based Superalloys Material on Its Microstructure and Wear Properties:MATERIALS,15):-
洪小英,肖贵乾(外),洪小英(学),Zhang, YC(外).Research on gradient additive remanufacturing of ultra-large hot forging die based on automatic wire arc additive manufacturing technology:INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY,116):2243-2254
周杰,周玉婷(学),舒倩(学),李世山(学),公冶凡娇(学),龙帅(外),邓和平(学).Deformation Mechanism and Constitutive Consideration for Ti-5Al-5Mo-5V-3Cr-1Zr Alloy Compressed at Elevated Temperatures:JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE,29):5104-5113
刘左发,周杰,刘左发(学),屈志远(学),汪西(学),Liang, Q(外), WJ(外).A precision sizing method for cold extruded sun gear with internal-external tooth shapes:INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY,115):3331-3344
权国政,鹿超龙(学),温志航(学),卢顺(外),张建生(外),董旭刚(外),周杰.电弧熔丝增材中锤击消除控制残余应力预设目标下介入温度寻优:塑性工程学报,28(7):175-183
刘左发,刘左发(学),Feng, WJ(外),Chen, YY(外).Modeling, analysis, and multi-objective optimization of cold extrusion process of clutch outer gear hub using response surface method and meta-heuristic approaches:INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY,116):229-239
彭世鑫,周杰,彭世鑫(学),王秋韵(学),张盟盟(学),舒倩(学),公冶凡娇(学),张建生(外),卢顺(外).Study on Microstructure and Numerical Simulation of Tailored Hot Stamping Tools Refabricated by Surfacing Co-Based Alloy:JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE,30):2732-2741
周杰,公冶凡娇(学),张谦(学),龙帅(外),周玉婷(学),李世山(学),彭世鑫(学),邓和平(学),张建生(外).Effect of cyclic heat treatment on microstructure and mechanical properties of Ti-5Al-5Mo-5V-3Cr-1Zr alloy:MATERIALS RESEARCH EXPRESS,8):-
龙帅,李世山(学),龙帅(外),周玉婷(学),周杰,Dai, QW(外),Cui, ML(外),Peng, Z(外).Deformation behavior of the Al-5.9Zn-2.1Mg-2.1Cu (wt%) alloy during isothermal pressure-holding after pre-deformation:MATERIALS TODAY COMMUNICATIONS,29):-

共33条 2/4

首页上页下页尾页页